ASME B16.47 WN Flange 150# - 900# DIN 2.4360 ASTM B564 UNS N04400
WN FF Flange
Other common names: Alloy 400
Monel 400 is a nickel-copper alloy (about 67% Ni – 23% Cu) that is
resistant to sea water and steam at high temperatures as well as to
salt and caustic solutions. Alloy 400 is a solid solution alloy
that can only be hardened by cold working. This nickel alloy
exhibits characteristics like good corrosion resistance, good
weldability and high strength. A low corrosion rate in rapidly
flowing brackish or seawater combined with excellent resistance to
stress-corrosion cracking in most freshwaters, and its resistance
to a variety of corrosive conditions led to its wide use in marine
applications and other non-oxidizing chloride solutions. This
nickel alloy is particularly resistant to hydrochloric and
hydrofluoric acids when they are de-aerated. As would be expected
from its high copper content, alloy 400 is rapidly attacked by
nitric acid and ammonia systems.
Monel 400 has great mechanical properties at subzero temperatures,
can be used in temperatures up to 1000° F, and its melting point is
2370-2460° F. However, alloy 400 is low in strength in the annealed
condition so, a variety of tempers may be used to increase the
strength.
What are the characteristics of Monel 400?
• Resistant to seawater and steam at high temperatures
• Excellent resistance to rapidly flowing brackish water or
seawater
• Excellent resistance to stress corrosion cracking in most
freshwaters
• Particularly resistant to hydrochloric and hydrofluoric acids
when they are de-aerated
• Offers some resistance to hydrochloric and sulfuric acids at
modest temperatures and concentrations, but is seldom the material
of choice for these acids
• Excellent resistance to neutral and alkaline salt
• Resistance to chloride induced stress corrosion cracking
• Good mechanical properties from sub-zero temperatures up to 1020°
F
• High resistance to alkalis
Chemical Composition, %
| C | Mn | S | Si | Ni | Cu | Fe |
| .30 max | 2.00 max | .024 max | .50 max | 63.0 min | 28.0-34.0 | 2.50 max |
Corrosion Resistant Monel 400
Alloy 400 is virtually immune to chloride ion stress corrosion
cracking in typical environments. Generally, its corrosion
resistance is very good in reducing environments, but poor in
oxidizing conditions. It is not useful in oxidizing acids, such as
nitric acid and nitrous. Nevertheless, it is resistant to most
alkalis, salts, waters, food products, organic substances and
atmospheric conditions at normal and elevated temperatures.
This nickel alloy is attacked in sulfur-bearing gases above
approximately 700° F and molten sulfur attacks the alloy at
temperatures over approximately 500° F.
Monel 400 offers about the same corrosion resistance as nickel but
with higher maximum working pressures and temperatures and at a
lower cost due to its superior ability to be machined.
In what applications is Monel 400 used?
• Marine engineering
• Chemical and hydrocarbon processing equipment
• Gasoline and freshwater tanks
• Crude petroleum stills
• De-aerating heaters
• Boiler feed water heaters and other heat exchangers
• Valves, pumps, shafts, fittings, and fasteners
• Industrial heat exchangers
• Chlorinated solvents
• Crude oil distillation towers
Fabrication with Monel 400
Alloy 400 can easily be welded by gas-tungsten arc, gas metal arc
or shielded metal arc processes using appropriate filler metals.
There is no need for post weld heat treatment, however, thorough
cleaning after welding is critical for optimum corrosion
resistance, otherwise there is the risk of contamination and
embrittlement.
Finished fabrications can be produced to a wide range of mechanical
properties when proper control of the amount of hot or cold working
and the selection of appropriate thermal treatments is done.
Like most other nickel alloys, Monel 400 is typically tough to
machine and will work harden. However, excellent results can e
obtained if you make the correct choices for tooling and machining.
ASTM Specifications
| Pipe Smls | Pipe Welded | Tube Smls | Tube Welded | Sheet/Plate | Bar | Forging | Fitting | Wire |
| B165 | B725 | B163 | | B127 | B164 | B564 | B366 | |
Mechanical Properties
Typical room temperature Tensile Properties of Annealed Material
| Product Form | Condition | Tensile (ksi) | .2% Yield (ksi) | Elongation (%) | Hardness (HRB) |
| Rod & Bar | Annealed | 75-90 | 25-50 | 60-35 | 60-80 |
| Rod & Bar | Cold-Drawn Stress Relieved | 84-120 | 55-100 | 40-22 | 85-20 HRC |
| Plate | Annealed | 70-85 | 28-50 | 50-35 | 60-76 |
| Sheet | Annealed | 70-85 | 30-45 | 45-35 | 65-80 |
| Tube & Pipe Seamless | Annealed | 70-85 | 25-45 | 50-35 | 75 max * |
Connection method:
flange (flange) connection is the two pipes, fittings or equipment,
first each fixed on a flange plate, two flange plate, add flange
pad, bolt together, completed the connection.Some pipe fittings and
equipment have already come with flange, also belong to flange
connection.Flange connection is an important connection in pipeline
construction.Flange connection is easy to use, can withstand
greater pressure.Flanged connections are widely used in industrial
piping.In the home, the pipe diameter is small, and is low
pressure, not visible flange connection.If in a boiler room or
production site, there are flanged pipes and equipment everywhere.
Product Attribute
| Place of Origin | China | Brand Name | BOYUE |
| Standard | ASME B16.5 | Type | Weld Neck Flange |
| ModelNumber | UNS N04400 | Thickness | Sch40s,Sch80s,sch160 |
| Packing | Ply-Wood Cases | Payment | 30%TT+70% Balance |
Supply Ability:30000Pieces / per Month
Packaging & Delivery
Packaging Details:Generally ply wooden case or following customer's
requirement.
Port:Shanghai/Tianjin
Commerce Clause
| Minimum Order Quantity | 1pcs |
| Price: | Depending on quantity |
| Payment Terms: | T/T or Western Union or LC |
| Supply Ability: | 3,0000pcs per month |
| Delivery Time: | 10-100 days depending on quantity |
| Packaging Details: | PLY-WOODEN CASE OR PALLET |
Why Choose Us
1.One-Stop Service,One Single Source.
2.No MOQ.
3.Best quality,competitive price
4.Fast Reply.
5.On-Time Delivery
6.Professional sales and technical team .
FAQ
Q1: Are you a factory or a trade company?
A1: We are a professional manufacturer for designing and producing
of Large-size products.(View Mor)
Q2: Do you make customized products or finished parts?
A2: All parts are custom made only, and in stock, we can produce
based on your drawings.
Q3: Will my drawing be e after you get it?
A3: Yes, we will not release your design to third party unless with
your permission.
Q4: What is the MOQ?
A4: Small order is acceptable, but the more, the cheaper.
Q5: How about the samples?
A5: We are happy to make prototype part or sample for clients to
ensure quality standard, but it’s charged according to your
drawing.
