Seamless Alloy Steel Pipe 2' SCH10S EN10216-2 X10 Hot Finished /
Cold DrawnCrMoVNb9-1
Seamless Steel Tube Specifications
Standard : EN10216-2
Outside Diameter: 325-1067 mm
Wall Thickness: 9.53-140 mm
Length: On the request
Mechanical properties
| Steel grade | Upper yield strength or proof strength ReH or Rp0,2 for Wall Thickness T min. | Tensile strength Rm | Elongation A min. % |
| T≤16 | 16<T≤40 | 40<T≤60 | 60<T≤100 | | I | T |
| MPa | MPa | MPa | MPa | MPa |
| P235GH | 235 | 225 | 215 | - | 360-500 | 25 | 23 |
| P265GH | 265 | 255 | 245 | - | 410-570 | 23 | 21 |
| 13CrMo4-5 | 290 | 290 | 280 | - | 440-590 | 22 | 20 |
| 10CrMo9-10 | 280 | 280 | 270 | - | 480-630 | 22 | 20 |
| 15NiCuMoNb5-6-4 | 440 | 440 | 440 | 440 | 610-780 | 19 | 17 |
| X10CrMoVNb9-1 | 450 | 450 | 450 | 450 | 630-830 | 19 | 17 |
Minimum proof strength Rp0,2 at elevated temperature
| Steel grade | Wall thickness mm | Minimum proof strength Rp0,2 MPa at temperature of °C |
| 100 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 550 | 600 |
| P235GH | ≤60 | 198 | 187 | 170 | 150 | 132 | 120 | 112 | 108 | - | - | - |
| P265GH | ≤60 | 226 | 213 | 192 | 171 | 154 | 141 | 134 | 128 | - | - | - |
| 13CrMo4-5 | ≤60 | 264 | 253 | 245 | 236 | 192 | 182 | 174 | 168 | 166 | - | - |
| 10CrMo9-10 | ≤60 | 249 | 241 | 234 | 224 | 219 | 212 | 207 | 193 | 180 | - | - |
| 15NiCuMoNb5-6-4 | ≤80 | 422 | 412 | 402 | 392 | 382 | 373 | 343 | 304 | - | - | - |
| X10CrMoVNb9-1 | ≤100 | 410 | 395 | 380 | 370 | 360 | 350 | 340 | 320 | 300 | 270 | 215 |
Appearance
1 The tubes shall be free from external and internal surface
defects that can be detected by visual examination.
2 The internal and external surface finish of the tubes shall be
typical of the manufacturing process and, where applicable, the
heat treatment employed. Normally the finish and surface condition
shall be such that any surface imperfections requiring dressing can
be identified.
3 It shall be permissible to dress, only by grinding or machining,
surface imperfections provided that, after doing so, the wall
thickness in the dressed area is not less than the specified
minimum wall thickness. All dressed areas shall blend smoothly into
the contour of the tube.
4 Any surface imperfection, which is demonstrated to be deeper than
5 % of the wall thickness T or 3 mm whichever is the smaller, shall
be dressed. This requirement does not apply to surface imperfection
with a depth equal or less 0,3 mm
5 Surface imperfections which encroach on the specified minimum
wall thickness shall be considered defects and tubes containing
these shall be deemed not to conform to this Part of EN 10216.
Leak Tightness
The tubes shall pass a hydrostatic test (see 11.8.1) or
electromagnetic test for leak-tightness.
Content of inspection documents
The content of the inspection document shall be in accordance with
prEN 10168.
The inspection certificate or inspection report shall contain the
following codes and information:
- commercial transactions and parties involved;
- description of products to which the inspection document applies;
- direction of the test pieces and testing temperature;
- tensile test;
- impact test if applicable;
- other tests (e.g. flattening);
- chemical composition on cast analysis (product analysis if
applicable);
- marking and identification, surface appearance, shape and
dimensional properties;
- leak-tightness test, NDT, material identification if applicable;
Test methods
1 Chemical analysis
2 Tensile test
2.1 tensile test at room temperature in accordance with EN 10002-1
2.2 tensile test at elevated temperature in accordance with EN
10002-5
3 Flattening test in accordance with EN 10233
4 Ring tensile test in accordance with EN 10237
5 Drift expanding test in accordance with EN 10237
6 Ring expanding test in accordance with EN 10236
7 Impact test in accordance with EN 10045-1
8 Leak tightness test
8.1 Hydrostatic test
8.2 Electromagnetic test in accordance with EN 10246-1
9 Dimensional inspection
10 Visual examination
11 Non-destructive test
| Place of Origin | China | Brand Name | BOYUE |
| Standard | ANSI, ISO, ASME, DIN, ASTM | Type | Seamless |
| ModelNumber | Alloy Steel Pipe | Thickness | SCH 5-SCH XXS |
| Packing | Depending on customer | Payment | 30%TT+70% Balance |
Supply Ability:40000Pieces / per Month
Packaging & Delivery
Packaging Details:Generally plywooden case or following customer's
requirement.
Port:Shanghai/Tianjin
Commerce Clause
| Minimum Order Quantity: | 1pcs |
| Price: | Depending on quantity |
| Payment Terms: | T/T or Western Union or LC |
| Supply Ability: | 40000 ton per month |
| Delivery Time: | 10-100 days depending on quantity |
| Packaging Details: | Depending on customer |
Why Choose Us
1. One-Stop Service,One Single Source.
2. No MOQ.
3. Best quality,competitive price
4. Fast Reply.
5. On-Time Delivery
6. Professional sales and technical team .
FAQ
Q1: Are you a factory or a trade company?
A1: We are a professional manufacturer for designing and producing
of Large-size products.(View Mor)
Q2: Do you make customized products or finished parts?
A2: All parts are custom made only, and in stock, we can produce
based on your drawings.
Q3: Will my drawing be e after you get it?
A3: Yes, we will not release your design to third party unless with
your permission.
Q4: What is the MOQ?
A4: Small order is acceptable, but the more, the cheaper.
Q5: How about the samples?
A5: We are happy to make prototype part or sample for clients to
ensure quality standard, but it’s charged according to your drawing
